Call: 603-352-0053 • Fax: 603-352-5424 • sales@turmoilcoolers.com   
Turmoil Oil and Coolant Coolers

 

 

      PRECISE TEMPERATURE CONTROL FOR PRECISION MACHINING

COOLERS BY
APPLICATION
COOLER
SELECTION
INQUIRY
FORM
SUPPORT
FORMS
HOW TO
ORDER
ABOUT
TURMOIL
HOME
Download our Catalog

Get Adobe Acrobat Reader

Turmoil Options & Accessories


Quick Links:  

CONDENSERS

  • HA High Ambient Condenser: Oversized condenser for operating in ambient's up to 110ºF.
  • W Water-Cooled Condenser: Eliminates heat dissipation to ambient. Supplied with condenser water-regulating valve for hookup to city (65ºF) or tower (85ºF) water.
  • NRC Non-Refrigerated Cooler. Uses central chilled water or ambient air instead of refrigeration. Saves space and maintenance. Chilled water must be at least 10ºF (6ºC) colder than lowest desired coolant temperature (R & RO models).
  • AR Remote Air-Cooled Condenser: Shipped separately from cooler. Eliminates heat dissipation to surrounding ambient. Remote installation by others.
  • WP WeatherProof construction for outdoor installation. Takes the heat outside by mounting the complete cooler outdoors.

[Back to Top]

TEMPERATURE CONTROLLERS

  • CTC Digital Temperature Controller for close temperature control within ±0.5º of set-point. Large display indicates both set point and coolant temperature.
  • ATC Ambient Tracking Controller. A dual-input, digital controller that allows the cooler to track the ambient (or machine bed) at a constant, adjustable differential. The controller displays
    both ambient and coolant temperatures.
  • ATC/CTC Combination ATC and CTC Controller allows operator to quickly switch between ambient tracking mode (ATC) and set-point mode (CTC).

[Back to Top]

Cleanable EvaporatorPIPING & EVAPORATOR

  • PS Pure System for de-ionized water applications. Coolant only comes in contact with stainless steel or plastic. Evaporator is all stainless steel coil or nickel brazed stainless steel plates.
  • NC Non-Copper for high-sulfur oils. Oil only comes in contact with stainless steel, steel, or iron. Evaporator is enhanced nickel brazed stainless steel plates.
  • CEV Cleanable Evaporator has removable end plates for in-place cleaning without disturbing plumbing or refrigeration lines. Only available for use with water-based coolants.
  • CHX Cleanable Heat Exchanger for use with oils or any coolant. The cooler recirculates water internally to a plate-type, water-to-oil heat exchanger that is easy to take apart and clean without disturbing plumbing connections.

[Back to Top]

INTERLOCKS

  • FS Low Flow Interlock. A flow switch is installed in-line and wired to the terminal strip for remote flow fault indication (R & RO Coolers).
  • LL Low Coolant Level. A level switch is installed in the tank and wired to the terminal strip for remote low coolant level indication (R & DI Coolers).
  • HT Temperature Fault. Contacts are provided to indicate that the coolant temperature is out of range.
  • FSM Flow Switch/Meter is provided with a needle valve that permits visual flow rate adjustment and adjustable low flow interlock setting.
  • LP Low Coolant Pressure Interlock. A pressure switch is installed in the discharge and wired to the terminal strip for remote low pump pressure indication.
  • RF Refrigeration Fault. Contacts are provided to indicate that the refrigeration pressures are too high or too low.
  • PO Pump On. Contacts are provided to indicate that the recirculating pump is on.
  • RE Remote On/Off. Contacts are provided to permit the start/stop of the cooler from a remote location.
  • RS Computer Interface. Temperature controllers are available with RS232 or RS485 computer ports.

[Back to Top]

In-Line FilterPUMPS & ACCESSORIES

  • OP Optional Pump for any requirement. Pump oil- or water based coolants at desired flow and pressure(RO & R models only).
  • ILF In-Line Filter. Suggested for installations with dirty or potentially dirty coolant to protect the evaporator from clogging. Supplied with a flow switch and a change filter warning light. A variety of filters and filter elements are available (available all models except DI).
  • ILH In-Line Heater warms up coolant to optimum operating temperature to prevent cold starts or to provide closer temperature control.
  • RC Rubber Casters available on all models for complete mobility.
  • PG Pressure Gauge available for Discharge and/or Input.
  • DT Dial Thermometer available for Discharge and/or Input.
  • FM Flow Meter provides accurate indication of coolant flow (R & IL models).

[Back to Top]

Optional WiringWIRING & SAFETY

  • LD Lever-Type Fused Disconnect installed on a NEMA-12 enclosure. Required by some electrical codes.
  • MC Multi-pin Connector to quickly interface cooler with machine. Can be supplied for both power and interlock connections.
  • JIC Automotive JIC Wiring. Coolers can be wired to meet specific automotive wiring specifications.
  • IEC International Wiring. Coolers meet the standards of the International Electro technical Commission (IEC) for machine safety.
  • CE Certificate of Compliance. Cooler to be provided with a CE tag and a Certificate of Compliance with CE Directives.
  • N4 NEMA-4 Electrical Enclosure. Waterproof.
  • OV Optional Voltages. Available on most models. Configures for almost any power supply, domestic or export.

[Back to Top]

Modified CoolersMODIFICATIONS

  • SP Special Paint Color. Match the cooler to your machinery.
  • SS All Stainless Steel Cabinet.
  • MOD Special Configuration. Special dimensions or component locations to fit the cooler into a particular space.
  • CIR Multiple Circuits. Cool more than one circuit from each cooler. All models are available with multiple IN and OUT connections for balanced or unbalanced flow.

Turmoil Manufacturing Co. • 735 West Swanzey Rd. • P.O. Box 583 • West Swanzey, NH 03469 USA
Call: 603-352-0053 • Fax: 603-352-5424